40 PINS 15 cm FEMALE TO FEMALE JUMPER WIRE (FLAT CABLE)

This flat cable can easily be stripped apart into a single (or multiple) jumper wires.
Features

contents: 1 pc of multi-colour flat cable (40 wires)
pre-cut, pre-stripped and pre-formed wires simplify and speed up prototyping work
easy to connect and disconnect
these wires are compatible with standard breadboards that have 0.1 inch grids

Specifications

length: 15 cm
diameter: 22-26 AWG
insulation material: PVC
conductor material: copper
type: female to female connector cable

GPS MODULE U-BLOX NEO-7M FOR ARDUINO

The NEO-7 series of standalone GNSS modules is built on the exceptional performance of the u-blox 7 GNSS (GPS, GLONASS, QZSS and SBAS) engine. The NEO-7 series delivers high sensitivity and minimal acquisition times in the industry proven NEO form factor.
Features

U-BLOX NEO-7N module, compact and excellent performance
parameters can be set via serial port and saved in EEPROM
with SMA interface, you can connect a variety of antenna, strong adaptability
compatible with 3.3 V / 5 V level for easy connection to a variety of microprocessor systems
back-up rechargeable battery on board
with micro USB, no need for USB-TTL tools
with TTL interface
onboard ceramic antenna
sample code: https://playground.arduino.cc/UBlox/GPS
evaluation software (U-Center) available for download

Specifications

supply voltage: 3.3 to 5 VDC (or by USB cable)
connections: VCC (+5 V), GND (ground), TX, RX, PPS (time pulse)
default baud rate: 9600 baud
dimensions: 4 x 2.5 x 1.5 cm
weight: 15 g

ELECTROMAGNET MODULE

High Quality Electric lifting magnet
Specifications

holding force: 25 N
working voltage: 5 V
working current: 400 mA
standby current: 200 uA
load weight: 1 kg
dimensions: 35 x 20 x 17 mm
weight: 25 g

DMX512 MODULE

This Arduino add-allows you to use the Arduino as a DMX master device (transmitter). This board is a simple circuit based around a driver chip (MAX-485 or SN 75176). With XLR 3 pin male DMX output connector. Pin1 = Signal Common, Pin2 = Data-, Pin3 = Data+ The board converts the Arduino signal voltage according to DMX (RS485). Impedance is 100 Ohm.
Specifications

working voltage: 5 V
DMX connection: XLR 3 pin
dimensions: 40 x 20 x 30 mm
weight: 10 g

RED LASER DIODE MODULE

This laser module produces a small intense light beam (650 nm, red).

Specifications
operating voltage: 5 V
operating current: 20 mA
wavelength: 650 nm
colour: red
dimensions: 18.5 mm x 15 mm [0.728 in x 0.591 in]
working temperature: -10°C - 40°C [14°F to 104°F]
output power: 1 mW

DIGITAL ROTARY ENCODER MODULE

A rotary encoder is an input device that indicates the rotating direction and how much the knob has been rotated. A rotary encoder is useful for for stepper and servo motor control.
Features

flat top
push-button capability
unlimited rotations
pins are right-angle to the knob, but you can connect them to a breadboard using male-female jumper wires
standard pin spacing: 2.54 mm (0.1 inch)

Specifications

working voltage: 0-5 V
type: incremental encoder
material: PCB + brass
cycles per revolution (CPR): 20
dimensions: 26 x 19 mm
weight: 10 g

8 CHANNEL RELAY MODULE

This 8-channel relay interface board can control various appliances and other equipments with high current. It can be controlled directly by any micro-controller.
Features

standard interface that can be controlled directly by any microcontroller
opto-isolated inputs
indicator LEDs for relay output status

Specifications

control input current (in1 to in4): 5 - 25 mA
control input voltage: 5 - 12 VDC
relay output: 250 VAC 10 A, 30 VDC 10 A (non-inductive)
dimensions: 57 x 138 mm
operating voltage: 5 V

1.3 INCH OLED SCREEN FOR ARDUINO (SH1106 DRIVER, SPI)

OLED displays have several advantages: low power consumption, bright, large viewing angle for better readability and high resolution.
Specifications

resolution: 128 x 64 dots
viewing angle: > 160°
working voltage: 3 - 5 V
recommended library: U8glib
interface: SPI
driver: SSH1106
working temperature: -30°C - 70°C
OLED colour: blue
dimensions: 35 x 33.5 mm

0.96 INCH OLED SCREEN WITH I2C FOR ARDUINO

OLED displays have several advantages: low power consumption, bright, large viewing angle for better readability and high resolution.
Specifications

resolution: 128 x 64 dots
viewing angle: > 160°
working voltage: 3 - 5 V
recommended library: U8glib
interface: I2C
driver: SSD1306
working temperature: -30°C - 70°C
OLED colour: blue
I/O level : 3.3 V and 5 V
dimensions: 27 x 27 mm

RGB DOT MATRIX BOARD & DRIVER BOARD BASED ON ATMEGA328

This Arduino based (ATmega328P) RGB LED matrix driver platform based gains three 8+6-bit channels of hardware PWM control thanks to its LED driver. Its design allows you to easily change or write firmware using the Arduino IDE.
Features

8 bits colours support with 6 bits correction for each colour in every dots
hardware 16 MHz PWM support
without any external circuits, play and shine
dedicated GPIO and ADC interface
hardware UART and IIC communication with easy cascading
24 constant current channels of 100 mA each
8 super source driver channels of 500 mA each
driver board is based on ATMEGA328 and works with IDE

Specifications

module dimensions: 60 x 60 x 16 mm
microprocessor: Atmega328P
indicator: PWR state
power supply: 5 to 7.5 VDC
cascade power connector: terminal blocks
program interface: UART/ISP (VMA440)
expansion socket: 100 mil bended pin header pair
communication protocols: UART/IIC
current consumption (except LED matrix): max. 40 mA
drive current (every channel): max. 500 mA
drive current ( every dot): max. 58 mA
circuit response time: 10 ns
RGB LED matrix colour resolution per dot: 16 M
UART baud rate: 9600 - 115200

FT232 USB TO TTL ADAPTOR 3.3/5 V

Use this module to program VMA439: RGB DOT MATRIX BOARD & DRIVER BOARD BASED ON ATMEGA328 through USB.
Features

single chip USB to asynchronous serial data transfer interface
data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels
transmit and receive LED drive signals
USB 2.0 Full Speed compatible
switchable 3.3 VDC and 5 VDC operation

Specifications

power supply: 5 VDC by USB cable (included)
micro USB connector
dimensions: 43 x 17 x 12 mm
weight: 5 g

SI4703 FM TUNER EVALUATION BOARD

The VMA444 is a radio and RDS receiver combined with an efficient 150 mW audio amplifier. This module is ideal if you want to create your own clock radio or if you want to add FM functionality to your projects.

Features
worldwide FM band support
digital low-IF receiver
automatic frequency control (AFC)
automatic gain control (AGC)
volume control
RDS/RBDS support
Arduino library available
150 mW amplifier stereo amplifier
level shifters 5 V -3.3V on board
Specifications
interface: I2C
power / logic level: 3.3 - 5 V
sensitivity: 1.7 µ emf
max. output power: 150 mW (8 Ohm)
default gain: 18 dB (8 x) (adjustable)
dimensions: 29 x 22 mm

PAM8610 DIGITAL POWER AMPLIFIER MODULE 2 x 10 W

The VMA446 (PAM8610) is a 10 W (per channel) stereo Class-D audio amplifier with DC volume control which offers low THD+N (0.1%), low EMI, and good PSRR thus high-quality sound reproduction. The 32 steps DC volume control has a +32 dB to -75 dB range.

Features
10 W @ 10% THD/channel output into an 8 Ohm load at 13 V
low noise: -90 dB
over 90% efficiency
32 step DC volume control from -75 dB to + 32 dB
shutdown/mute/fade function
over current, thermal and short-circuit protection
low THD+N
low quiescent current
pop noise suppression
Specifications
supply voltage (Vdd): 7 to +15 V
input voltage range (Vi):
mute, Vref, volume, fade: 0 to +6.0 V
SD: -0.3 to Vdd
RINN, RINP, LINN, LINP: -0.3 to +6.0 V
junction temperature range (Tj): -40 to +125 °C
output power @ 8 Ohm: 10 W

MINI PERISTALTIC PUMP 6 V

A peristaltic pump is a type of positive displacement pump used for pumping a variety of fluids.

Features
ultra silent (< 40 dB)
maintenance free
positive inversion
non polluting
accurate repeatability
dry running, self priming
comes with stop valve funtion to prevent backflow in both ways
not for food contact
Specifications
power supply: 6 VDC / 5 W
tube dimensions: 2.0 x 4.0 mm
tube material: silicon
tube life: > 200 h
flow rate: >= 39 ml / min
dimensions : 65 x 40 mm
weight: 95 g
connections: solder tag 3 mm

2 WHEEL DRIVE MOTOR CHASSIS ROBOTICS KIT

This kit makes creating your own robot easier than ever.
Features

pre-drilled mounting plates
one DC motor + gearbox per wheel

Specifications

motor voltage: 5-10 VDC

TRANSPARENT BOX CASE SHELL FOR ARDUINO UNO R3

Specifications

material: acrylic
dimensions: 79 x 65 x 21 mm
weight: 53 g

TRANSPARENT BOX CASE SHELL FOR ARDUINO® MEGA 2560R3

Specifications

material: acrylic
dimensions: 114 x 65 x 18 mm
weight: 72 g

PROJECT HOLDER FOR ARDUINO UNO DEVELOPMENT BOARD + BREADBOARD

The project holder allows you to attach the Arduino UNO and the included breadboard together. It contains two grooves (one groove size is 88 x 60 mm), which is the just right size to fit a 400 holes breadboard, the other groove is for the Arduino UNO. The position of 4 M3 screw holes fits the Arduino UNO mounting holes. The holder comes with 4 screws (M3 x 8).
Specifications

dimensions: 160 x 106 mm
max. breadboard size: 88 x 60 mm
weight: 50 g

MINI ANALOG SERVO - 9 g

Specifications

dimensions: 21.5 x 12 x 22.7 mm
voltage: 4.8 to 6 VDC
weight: 9 g
speed: 0.09 sec. for 60° at 6 V
torque: 1.4 kg.cm at 6 V
working temperature: -15° C to 50 °C
connection type: 3 wires: brown (gnd) - red (+) - orange (signal)
connection diagram: http://arduino.cc/en/Tutorial/Sweep

270° ROBOT DIGITAL DOUBLE SHAFT SERVO KIT

Specifications

operating speed (at no load): 0.14 sec/ 60° at 7.2 V
running current (at no load): 100 mA at 7.2 V
stall torque (at lock): 15 kg at 7.2 V
stall current (at lock): 1.5 A at 7.2 V
idle current (at stopped): 5 mA
operating frequency: 50 - 330 Hz
operating angle: 90°/135° (from 1000 to 2000 usec)
neutral position: 1500 usec
dead band width: 3 usec
rotating direction: counter clockwise (from 1000 to 2000 usec)
pulse width range: from 500 to 2500 usec
overall dimension: 40 x 20 x 40.5 mm
weight: 64 g
connector wire gauge: 28 PVC
connector wire length: 320 ± 5 mm
horn gear spline: 25T/5.80
reduction ratio: 310:1
operating temperature range: -10°C - 50°C
operating voltage: 5 V - 7.2 V
connection: orange = PWM, red = VCC , brown = GND